Wednesday, 9 December 2015

Christmas Cracker Cushion

Hello! Thought I'd pop in and show you what I did with my Christmas Cracker from the free block tutorial I shared. I turned it into a cushion cover:

I simply added borders to get to the desired size, basted and quilted as normal, then added a zippered back and machine-sewn binding. 

A simple flap of folded fabric conceals the zipper:

A zippered cushion closure is so much nicer than an envelope backing - no gaping! - and is not at all difficult. I think I need to stock up on zippers and make a few more. My naked cushions would probably appreciate it. ;)

Bye for now, 

Hope x 

Tuesday, 8 December 2015

Christmas Cracker - A Free Quilt Block Tutorial

Season's Greetings! I have a fun, festive quilt block tutorial to share with you today - a Christmas Cracker! I've used leftover 5" charm squares, but jelly roll strips are ideal, or anything you can cut a long enough 2.5" strip from. It's pretty quick too - which is lucky, since Christmas is not far away... so let's get to it!

For a single block you will need:

  • 2 coordinating, 5" charm squares - these will be Fabric A (the largest pieces of the cracker) and Fabric B (the smaller pieces of the cracker);
  • 2.5" x WOF strip background fabric

Use a quarter inch seam allowance, unless specified otherwise.

Start by pressing your fabric to remove all creases. Use a little steam or spray starch, and be careful not to distort the fabric. Allow to cool.

Cut one charm square (Fabric A) into two rectangles, 2.5" x 5", then from one of these cut one piece, 2.5" x 4.5", and from the other cut two pieces, 2.5" x 2.25".

Cut the other charm square (Fabric B) into two rectangles, 2.5" x 5". From these cut a total of six rectangles, 2.5" x 1.25".

From your 2.5" background fabric strip, cross-cut 4 pieces, 1" x 2.5". Cross-cut these into two squares each, 1" x 1", for a total of 8 squares. Set the rest of the background fabric aside for now.

Draw a diagonal line, corner to corner, across the back of each of your 1" background squares. This will be your sewing line.

Lay out your pieces as shown, making sure you have the 2.25" Fabric A rectangles oriented the correct way, with the 2.25" edge running left to right.

Sew each end Fabric B piece to its adjacent Fabric A 2.25" piece. Press seams to Fabric A.

Place a square on the corners of the four inner Fabric B pieces, face down, as shown. Pay careful attention to the direction of the sewing lines.

Making sure edges are flush, sew along the sewing lines a smidgen to the seam allowance side of the line (i.e. the outside corner of the square).

Press to set seams. Finger press open, pressing the seams in two of the units (one from each side of the cracker) towards the background fabric, and the other two units to Fabric B. When pressing seams to the background, your corners and edges should all line up:

When pressing to Fabric B, your background should neatly replace the corners of Fabric B. In both cases you should end up with a neat 2.5" x 1.25" rectangle.

When you're sure everything lines up, press seams with your iron - being careful of your fingers with the small pieces. Trim seam allowances to a quarter inch.

Now you will have two pairs, the back of which should look like this:

Sew each pair together, nesting the seams where they meet. You should be able to feel them 'lock' together.

Press seams to one side - whichever side sits nicest. Lay out your pieces again as shown:

Sew the pieces together to finish the cracker, pressing seams to Fabric A.

And from the back:

To finish the block, make sure your cracker is freshly pressed and cooled and measure the length (i.e. the longest side). It should be 12.5".

From your 2.5" background strip, cross-cut cut two rectangles the length of your cracker.

Pinning at the centre, quarter way points and each end, sew a background strip to the top, and one to the bottom of your cracker. Press seams to the background.

Congratulations, you've finished your block!

Note: When complete, block should measure 12.5" x 6.5" (including seam allowance all round). If you want a border all round, rather than just the top and bottom, you will need two more pieces, 6.5" x 2.5", for each end. Depending on how long your 2.5" strip is, you may need more background fabric

If you make something from this tutorial, I'd love to see it! Add a link in the comments, send me an email, or tag me on Instagram (@hopetn). You can see what I did with my block here.

Happy sewing!

Hope x

Thursday, 3 December 2015

New Leaf - A New Pattern

Happy December! I am pleased and excited to start the month with a new pattern release! I call this one "New Leaf".

The quilt is pre-cut friendly - Jelly Rolls, Sushi Rolls etc. can be used for the main 40.5" x 48.5" lap quilt, and the 12.5" square mini quilt uses two fat quarters. Yes, there's a mini quilt included in the pattern, no extra charge. :) Here's the version I made using a couple of Bonnie & Camille prints:

I used half a Moda Jelly Roll for the colours and yardage for the grey in my lap quilt. I absolutely adore these fabrics by Basic Grey from their Fresh Cut collection. The other half of the Jelly Roll is destined to (one day) become a coordinating quilt of the same design.

As usual, I've tried my best to make this pattern amazing value. There are loads of tips, step by step instructions and illustrations, as well as a couple of variations including an ombre version:

I've also included colouring pages at the end of the pattern so you can play with colour before deciding on your fabrics.

I really and truly love this quilt and the pattern I've produced. It's not hard to put together, is suitable for beginners, plus I'm always happy to offer assistance if needed. I hope you'll give it a go!

You can buy the pattern here or if you're in the EU, through my Etsy Store.

Happy Sewing!

Hope x